- 金币
- 1795
- 社区知名度
- 11
- 威望
- 85
- 积分
- 3750
- 帖子
- 2
- 精华
- 1
- UID
- 553139
|
本帖最后由 爱在民大 于 2016-6-8 03:40 编辑
自从买了罐头SBBN025后,发现是石英机芯就在想以后怎样换电池,发现大家都有这烦恼,所以找了些资料给大家参考,
OK, let’s make a start, what tools for the job? – BTW the hex screws shroud requires a 1.5mm Hex key, Jaxa type case remover, Blade to pop off the bezel, small screwdriver for the battery retaining screw, case/movement holder.
Pic 1 –Remove the Hex screws
Pic 2 –Shroud removed, revealing dirt – I cleaned this up to avoid any getting in the case later on.
Report this image
Pic 3 –Slipping a flat blade between the case and bezel, pop off the bezel – this should be easy. In this pic you can see the two flat bezel springs still in thecase.
Report this image
Pic 4 - The flat bezel springs sit in a groove and are easily removed with a small screwdriver or similar
Report this image
Pic 5 - I have removed the strap and popped the case into a movement/case holder, you will need to secure the case so that you can get good leverage to unscrew the crystal retaining ring.
Report this image
Pic 6 –Here the crystal retaining screw has been removed using a Jaxa type caseback remover. Ensure the remover sits properly within three grooves, apply even pressure and unscrew anti clockwise. These are normally hand tight some can be tough but keep even pressure or you may slip and scratch the crystal orcase.
Report this image
Pic 7 –Under the crystal retaining ring sits a nylon band which ensures the rubber gasket below it is evenly pressed and shaped to provide a maximum seal.
Report this image
Pic 8 –This shows the crystal out but the crystal gasket still in place. Removing crystal I found to be quite tricky, it sits on the rubber gasket under pressure so it is well bedded in and requires very gentle persuasion with a small flatend object, preferable made of plastic or wood. You can use a flat head screwdriver, but you can end up damaging the gasket or the crystal.
Report this image
Pic 9 –This shows the crystal far left, then the rubber gasket and the minute chapter ring. The chapter ring has two grooves cut into it that match to one dial feet and the crown. This ensures that the markers line up perfectly when refitting.
Report this image
Pic 10 –Here you see a gasket that sits around the movement, this should be removed to get access to the crown release button.
Report this image
Pic 11 –This shows the crown release button and it sits just north of the crown,unscrew the crown, on the two occasions I have removed the crown from a 7C46 I didn’t pull it out to 1st or 2nd position prior to removal, just unscrew the crown, depress gently the release button and wiggle the crown with gentle pulling force, and it should pop out.
Report this image
Pic 12 –Case, movement and crown
Report this image
Pic 13 –With the crown removed there is nothing holding the movement in the case, so be careful and turn the case over ensuring you can grip the edges of the movement/dial. Then you will need to pop the movement into the holder. Remove completely the screw holding the battery retaining clip, don’t think you can nudge the battery out, you won’t. Replace battery and pop the retaining clip back and spend 30 minutes putting the little bugger of a screw back in .
Report this image
Pic 14& 15 – Here is the case all nicely cleaned, I really like this case, and you can see it is a great piece of design and engineering, each groove has a purpose and the base has a raised plate where the movement sits.
Report this image
Now thebattery is replaced and you have cleaned and greased (very little required) the gaskets put it back together. Do you need to replace the gaskets? Well some will swear by it, but I have found that certainly on these modern Seiko’s the gasket shape is fine and can be used again, if it has deteriorated or out of shape then of course in needs replacing.
Pic 16 –Once completed put on wrist and admire your handy work J
Report this image
I want to pay credit to Dr Seiko for his tutorial on the 1000m divers, without I wouldn’t have ever dared to attempt this.
|
-
16.jpg
(99.34 KB, 下载次数: 4)
-
15.jpg
(98.21 KB, 下载次数: 1)
-
14.jpg
(78.66 KB, 下载次数: 1)
-
13.jpg
(106.94 KB, 下载次数: 1)
-
12.jpg
(56.64 KB, 下载次数: 1)
-
11.jpg
(114.92 KB, 下载次数: 1)
-
10.jpg
(107.67 KB, 下载次数: 1)
-
9.jpg
(42.28 KB, 下载次数: 2)
-
8.jpg
(49.82 KB, 下载次数: 1)
-
7.jpg
(92.13 KB, 下载次数: 1)
-
6.jpg
(84.18 KB, 下载次数: 2)
-
5.jpg
(85.05 KB, 下载次数: 1)
-
4.jpg
(47.63 KB, 下载次数: 1)
-
3.jpg
(63.63 KB, 下载次数: 2)
-
2.jpg
(57.47 KB, 下载次数: 1)
-
1.JPG
(53.98 KB, 下载次数: 1)
-
总评分: 威望 + 30
金币 + 50
社区知名度 + 5
查看全部评分
|